Just How to Install a Bath Tub
Just How to Install a Bath Tub
Blog Article
The writer is making a few good annotation relating to Installing A Bathtub overall in this article below.
Mounting a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your restroom if you have actually currently acquired a new tub and don't need to alter the plan of your previous water pipelines.
Your devices and also product checklist ought to make up the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly bothersome due to the limited accessibility that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the required placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water supply and also inspect all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bath tub and additionally inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait up until the bath tub has been made use of at least once as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the manufacturer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind must be linked to the tap ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the tiles making use of water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that piece of writing about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the internet. Kindly set aside a second to share this entry if you liked it. Thanks a lot for going through it.
Book Maintenance Report this page